Mitsubishi Electric MELSEC-L LD75D, Руководство пользователя

Страница: 676 / 818

674
Parameter
981 OPR direction error
■ Description
The set value of the OPR basic parameter "OPR
direction" is outside the setting range.
■ Operation status at error occurrence
The LD75 READY signal (X0) does not turns ON.
■
Action
With the setting brought into the setting range,
turn the PLC READY signal [Y0] from OFF to ON.
■ Buffer memory address
Axis 1: 71
Axis 2: 221
Axis 3: 371
Axis 4: 521
■
Setting range
0, 1
982 OP address setting error
■ Description
The set value of the OPR basic parameter "OP
address" is outside the setting range.
■
Operation status at error occurrence
The LD75 READY signal (X0) does not turns ON.
■ Action
With the setting brought into the setting range,
turn the PLC READY signal [Y0] from OFF to ON.
■
Buffer memory address
Axis 1: 72, 73
Axis 2: 222, 223
Axis 3: 372, 373
Axis 4: 522, 523
■ Setting range
• [mm] [inch] [pulse]: -2147483648 to
2147483647
• [degree]: 0 to 35999999
983 OPR speed error
■ Description
• The set value of the OPR basic parameter "OPR
speed" is outside the setting range.
• The set value of the OPR basic parameter "OPR
speed" is smaller than the bias speed at start.
■
Operation status at error occurrence
The LD75 READY signal (X0) does not turns ON.
■ Action
• Set the value within the setting range.
• Set the speed to the bias speed at start or
higher. (

Page 140, Section 5.2.5)
■
Buffer memory address
Axis 1: 74, 75
Axis 2: 224, 225
Axis 3: 374, 375
Axis 4: 524, 525
■ Setting range
1 to 4000000 [pulse/s], 1 to 2000000000 [

10
-2
mm/min or other]
984 Creep speed error
■
Description
• The set value of the OPR basic parameter
"Creep speed" is outside the setting range.
• The set value of the OPR basic parameter
"Creep speed" is larger than the OPR speed.
• The set value of the OPR basic parameter
"Creep speed" is smaller than the bias speed at
start.
■ Operation status at error occurrence
The LD75 READY signal (X0) does not turns ON.
■
Action
• Set the value within the setting range.
• Set the speed to that below the OPR speed.
• Set the value to the bias speed at start or
higher. (  Page 140, Section 5.2.5)
■ Buffer memory address
Axis 1: 76, 77
Axis 2: 226, 227
Axis 3: 376, 377
Axis 4: 526, 527
■
Setting range
1 to 4000000 [pulse/s], 1 to 2000000000 [

10
-2
mm/min or other]
985 OPR retry error
■ Description
The set value of the OPR basic parameter "OPR
retry" is outside the setting range.
■
Operation status at error occurrence
The LD75 READY signal (X0) does not turns ON.
■ Action
With the setting brought into the setting range,
turn the PLC READY signal [Y0] from OFF to ON.
■
Buffer memory address
Axis 1: 78
Axis 2: 228
Axis 3: 378
Axis 4: 528
■ Setting range
0, 1
Classification
of errors
Error
code
Error name Operation status at error occurrence
Action/Related buffer memory address/Set
range (Setting with program)