Mitsubishi Electric MELSEC-L LD75D, Руководство пользователя

Страница: 665 / 818

663
CHAPTER 15 TROUBLESHOOTING
15
15.
5
List
of
E
rrors
Positioning
operation
544 Outside radius range
■
Description
The arc radius exceeds 536870912.
■ Operation status at error occurrence
At start: The system will not operate.
During operation: The system will stop immediately.
■
Action
Correct the positioning data. (  Page 391,
Section 9.2.10, Page 395, Section 9.2.11)
■ Buffer memory address

Page 152, Section 5.3
■
Setting range
Maximum radius: 536870912
545
Control system LOOP
setting error
■
Description
A "0" is set for number of repetitions of the control
system "LOOP".
■ Operation status at error occurrence
The system stops operation.
■ Action
Set 1 to 65535 for number of repetitions of the
"LOOP". (

Page 454, Section 9.2.24)
■
Buffer memory address
 Page 152, Section 5.3
■ Setting range
LOOP to LEND: 1 to 65535
546
Illegal setting of ABS
direction in unit of degree
■ Description
The setting value of ABS direction in the unit of
degree is as follows.
• Set outside the setting range.
• A figure other than "0" is set when the software
stroke limit is valid.
■
Operation status at error occurrence
At start: The system will not operate.
During operation: The system decelerates to a stop.
(Note that, in the continuous positioning control and
continuous path control, the system continues
operating with the setting set at the time of start
even if the setting is changed during the operation.)
■ Action
• Set the ABS setting direction in the unit of
degree within the setting range.
• Set "0" when the software stroke limits are
valid. (

Page 355, Section 9.1.5)
■
Buffer memory address
• ABS setting direction in the unit of degree
Axis 1: 1550
Axis 2: 1650
Axis 3: 1750
Axis 4: 1850
■ Setting range
0: Shortcut
1: ABS clockwise
2: ABS counterclockwise
■
Action
• Invalidate the software stroke limit. (To
invalidate, set the software stroke limit upper
limit value to be equal to the software stroke
limit lower limit value.) (
 Page 355, Section
9.1.5)
■ Buffer memory address
• Software stroke limit upper limit
Axis 1: 18, 19
Axis 2: 168, 169
Axis 3: 318, 319
Axis 4: 468, 469
• Software stroke limit lower limit
Axis 1: 20, 21
Axis 2: 170, 171
Axis 3: 320, 321
Axis 4: 470, 471
■
Setting range
• [mm] [inch] [pulse]: -2147483648 to
2147483647
• [degree]: 0 to 35999999
553 M code ON timing error
■ Description
The setting value of the positioning data "M code
ON signal output timing" is outside the range.
■ Operation status at error occurrence
At start: The system will not operate.
During operation: The system stops with the setting
(deceleration stop/sudden stop) of the detailed
parameter 2 Sudden stop selection (stop group 3).
■
Action
Correct the positioning data "M code ON signal
output timing" to 0 to 2.
■ Buffer memory address

Page 152, Section 5.3
■
Setting range
0: Use the set value in "[Pr.18] M code ON signal
output timing".
1: WITH mode
2: AFTER mode
554
Interpolation speed
designation method error
■ Description
The setting value of the positioning data
"Interpolation speed designation method" is outside
the range.
■
Operation status at error occurrence
At start: The system will not operate.
During operation: The system stops with the setting
(deceleration stop/sudden stop) of the detailed
parameter 2 Sudden stop selection (stop group 3).
■ Action
Correct the positioning data "Interpolation speed
designation method" to 0 to 2.
■ Buffer memory address

Page 152, Section 5.3
■ Setting range
0: Use the set value in "[Pr.20] Interpolation
speed designation method".
1: Composite speed
2: Reference axis speed
Classification
of errors
Error
code
Error name Operation status at error occurrence
Action/Related buffer memory address/Set
range (Setting with program)