Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 1222

background image

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 37).

Step 4.

Remove PCI riser-card assembly (see “Removing a PCI riser-card assembly” on page 37).

Step 5.

Align the flash device with the connector on the system board and push it into the USB connector
until it is firmly seated.

Step 6.

Pull up the blue locking collar to lock the flash device into the USB connector.

00

00

00

00

00

0

0

00

000

000

000

000

000

USB embedded
hypervisor
flash device

Lockbar

Figure 119. USB hypervisor flash device installation

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on
page 136.

Note:

You must configure the server to boot from the hypervisor USB drive. See Chapter 3 “Configuration

information and instructions” on page 141 for information about enabling the embedded hypervisor.

Installing an additional microprocessor and heat sink

Use this information to install an additional microprocessor and heat sink.

The following notes describe the type of microprocessor that the server supports and other information that
you must consider when you install a microprocessor and heat sink:

• Microprocessors are to be installed only by trained technicians.

Installing optional devices

127

«
...
137
138
139
140
141
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3650 M4 BD 5466

Бренд: Wyse Страницы: 6

Бренд: US Robotics Страницы: 156

Бренд: Digital Equipment Страницы: 73

Бренд: BELINEA Страницы: 53

Бренд: Cable-Tronix Страницы: 33

Бренд: Conceptronic Страницы: 127

Бренд: HIKVISION Страницы: 13

EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0

Бренд: Edimax Страницы: 118

iPlanet Web Server

Бренд: Sun Microsystems Страницы: 62

SC450NX - Server Platform - 0 MB RAM

Бренд: Intel Страницы: 200

Express5800/E120d-1

Бренд: NEC Страницы: 4

Express5800/B140a-T

Бренд: NEC Страницы: 19

Express5800/B120f-h

Бренд: NEC Страницы: 21

Express5800/GT110b

Бренд: NEC Страницы: 27

Express5800/GT110e-S

Бренд: NEC Страницы: 34

Express5800/B110d

Бренд: NEC Страницы: 19

Express5800/A2040d

Бренд: NEC Страницы: 20

Express5800/D120h

Бренд: NEC Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды