Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 624 | Manualshive

Страница: 624 / 1222

background image

CIM Information

Prefix:

PLAT

ID:

0131

User Response

1. Make sure the DIMM is installed correctly.

2. If the DIMM was disabled because of a memory fault (memory uncorrectable error or memory

logging limit reached), follow the suggested actions for that error event and restart the server.

3. Check the IBM support website for an applicable retain tip or firmware update that applies to

this memory event. If no memory fault is recorded in the logs and no DIMM connector error LED
is lit, you can re-enable the DIMM through the Setup utility or the Advanced Settings Utility (ASU).

•

806f040c-2009ffff : [PhysicalMemoryElementName] Disabled on Subsystem

[MemoryElementName]. (DIMM 9)

This message is for the use case when an implementation has detected that Memory has been Disabled.

May also be shown as 806f040c2009ffff or 0x806f040c2009ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0131

User Response

1. Make sure the DIMM is installed correctly.

2. If the DIMM was disabled because of a memory fault (memory uncorrectable error or memory

logging limit reached), follow the suggested actions for that error event and restart the server.

3. Check the IBM support website for an applicable retain tip or firmware update that applies to

this memory event. If no memory fault is recorded in the logs and no DIMM connector error LED
is lit, you can re-enable the DIMM through the Setup utility or the Advanced Settings Utility (ASU).

•

806f040c-200affff : [PhysicalMemoryElementName] Disabled on Subsystem

[MemoryElementName]. (DIMM 10)

This message is for the use case when an implementation has detected that Memory has been Disabled.

May also be shown as 806f040c200affff or 0x806f040c200affff

612

Lenovo System x3650 M4 Installation and Service Guide

«
...
622
623
624
625
626
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3650 M4 BD 5466

Бренд: Vitek Страницы: 2

Бренд: Raidon Страницы: 20

SuperServer 1029U-T Series

Бренд: Supermicro Страницы: 1

Бренд: Intermec Страницы: 232

Бренд: HIKVISION Страницы: 31

Бренд: Zeiss Страницы: 12

Бренд: Arris Страницы: 6

BladeCenter HS22

Бренд: IBM Страницы: 1

Бренд: IBM Страницы: 4

eServer 250 xSeries

Бренд: IBM Страницы: 84

8682 - Eserver xSeries 350

Бренд: IBM Страницы: 174

Бренд: IBM Страницы: 145

Бренд: IBM Страницы: 221

G4-20G-010-192T

Бренд: Viavi Страницы: 12

NETWORK SATELLITE 5.3.0 - CHANNEL MANAGEMENT

Бренд: Red Hat Страницы: 318

MultiAccess MA220

Бренд: Multitech Страницы: 80

Multi-Port Fast Ethernet Print Server FPS-3121

Бренд: Planet Страницы: 12

Бренд: 360 Systems Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды