Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 431

Страница: 431 / 1222

Warning - Power

SNMP Trap ID

164

CIM Information

Prefix:

IMM

ID:

0131

User Response

Information only; no action is required.

•

40000084-00000000 : IMM firmware mismatch between nodes [arg1] and [arg2]. Please attempt to

flash the IMM firmware to the same level on all nodes.

A mismatch of IMM firmware has been detected between nodes

May also be shown as 4000008400000000 or 0x4000008400000000

Severity

Error

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0132

User Response

Attempt to flash the IMM firmware to the same level on all nodes.

•

40000085-00000000 : FPGA firmware mismatch between nodes [arg1] and [arg2]. Please attempt

to flash the FPGA firmware to the same level on all nodes.

A mismatch of FPGA firmware has been detected between nodes

May also be shown as 4000008500000000 or 0x4000008500000000

Severity

Error

Serviceable

Automatically notify support

Alert Category

System - Other

Appendix A. Integrated management module II (IMM2) error messages

419

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды