Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 1197

Страница: 1197 / 1222

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-905-000 : Tape Test Failed

Tape Test Failed. Software error: invalid request.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. If the system has stopped responding, turn off and restart the system.

2. Check the system firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

3. Run the test again.

4. If the system has stopped responding, turn off and restart the system.

5. Make sure that the drive firmware is at the latest level.

6. Run the test again.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-906-000 : Tape Test Failed

Tape Test Failed. Unrecognized error.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

Appendix C. DSA diagnostic test results

1185

«
...
1195
1196
1197
1198
1199
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды