Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 348

Страница: 348 / 1222

Figure 252. Thermal grease

Remove the plastic protective cover from the bottom of the heat sink.

Position the heat sink over the microprocessor. The heat sink is keyed to assist with proper
alignment.

Figure 253. Heat sink installation

Align and place the heat sink on top of the microprocessor in the retention bracket, thermal
material side down.

Press firmly on the heat sink.

Rotate the heat sink retention module release lever to the closed position and hook it
underneath the lock tab.

Step 11. Reinstall the air baffle (see “Replacing the air baffle” on page 242).

Step 12. Install the cover (see “Replacing the cover” on page 240).

Step 13. Slide the server into the rack.

Step 14. Reconnect the power cords and any cables that you removed.

Step 15. Turn on the peripheral devices and the server.

336

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды