Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 1198

Страница: 1198 / 1222

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Make sure that the drive firmware is at the latest level.

4. Rerun the test after upgrading to the latest firmware level.

5. Make sure that the DSA Diagnostic code is at the latest level.

6. Run the test again.

7. Check the system firmware level and upgrade if necessary.

8. Run the test again.

9. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-907-000 : Tape Test Failed

An error was found in the block address somewhere.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-908-000 : Tape Test Failed

An error was found in getting tape capacity.

Recoverable

Severity

1186

Lenovo System x3650 M4 Installation and Service Guide

«
...
1196
1197
1198
1199
1200
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды