Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 300

Страница: 300 / 1222

Replacing an optional ServeRAID upgrade adapter memory module

Use this information to replace an optional ServeRAID upgrade adapter memory module.

To install an optional ServeRAID upgrade adapter memory module, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 240).

Step 4.

Connect the battery/flash power module cable to the ServeRAID upgrade adapter memory module.

Battery cable

ServeRAID memory module

Figure 200. ServeRAID upgrade adapter memory module and battery cable

Flash power
module cable

ServeRAID memory module

Figure 201. ServeRAID upgrade adapter memory module and flash power module cable

Step 5.

Attach the three pegs to the ServeRAID upgrade adapter memory module and install the ServeRAID
upgrade adapter memory module into the system board.

288

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды