Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 1222

background image

PCI riser-card assembly LEDs

The following illustration shows the light-emitting diodes (LEDs) on the PCI riser-card assembly.

Note:

Error LEDs remain lit only while the server is connected to power.

00

0000

0000

0000

00

0000

0000

0000

0000000

0000000

0000000

0000000

000

000

000

000

UpperPCI slot error LED

Center PCI slot error LED

Lower PCI slot error LED

Figure 21. PCI riser-card assembly LEDs

Installation guidelines

Use the installation guidelines to install the Lenovo System x3650 M4 Type 7915.

Attention:

Static electricity that is released to internal server components when the server is powered-on

might cause the system to halt, which might result in the loss of data. To avoid this potential problem,
always use an electrostatic-discharge wrist strap or other grounding system when removing or installing a
hot-swap device.

Before you install optional devices, read the following information:

• Read the safety information in “Safety” on page v, the guidelines in “Working inside the server with the

power on” on page 36, and “Handling static-sensitive devices” on page 36. This information will help
you work safely.

• Make sure that the devices that you are installing are supported. For a list of supported optional devices

for the server, see http://www.lenovo.com/ serverproven/.

• When you install your new server, take the opportunity to download and apply the most recent firmware

updates. This step will help to ensure that any known issues are addressed and that your server is ready
to function at maximum levels of performance. To download firmware updates for your server, go to
http://www.ibm.com/support/ fixcentral.

Important:

Some cluster solutions require specific code levels or coordinated code updates. If the

device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution
before you update the code.

For additional information about tools for updating, managing, and deploying firmware, see the
ToolsCenter for System x and BladeCenter at http://publib.boulder.ibm.com/infocenter/toolsctr/v1r0/.

• Before you install optional hardware, make sure that the server is working correctly. Start the server, and

make sure that the operating system starts, if an operating system is installed, or that a 19990305 error
code is displayed, indicating that an operating system was not found but the server is otherwise working

34

Lenovo System x3650 M4 Installation and Service Guide

«
...
44
45
46
47
48
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3650 M4 BD 5466

Бренд: Datacom Страницы: 89

Sun Blade T6340

Бренд: Sun Oracle Страницы: 82

Sun Fire Netra 1280

Бренд: Sun Microsystems Страницы: 10

Бренд: IBM Страницы: 1730

ReadiManagerSE200

Бренд: Polycom Страницы: 4

Бренд: Black Box Страницы: 4

Бренд: Black Box Страницы: 12

9000 APPLIANCE SERIES

Бренд: Arcserve Страницы: 14

Бренд: Adaptec Страницы: 6

Бренд: Supero Страницы: 106

Бренд: Supero Страницы: 108

Бренд: Intel Страницы: 179

Бренд: GRASS VALLEY Страницы: 106

Бренд: Seagate Страницы: 69

UniServer B5800 G3

Бренд: H3C Страницы: 78

Бренд: OSS Страницы: 46

Бренд: Gateway Страницы: 176

Бренд: Aaeon Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды