Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 776

Страница: 776 / 1222

•

81010901-1001ffff : Numeric sensor [NumericSensorElementName] going high (upper critical)

has deasserted. (PCI Riser 1 Temp)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has deasserted.

May also be shown as 810109011001ffff or 0x810109011001ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

No action; information only.

•

81010901-1002ffff : Numeric sensor [NumericSensorElementName] going high (upper critical)

has deasserted. (PCI Riser 2 Temp)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has deasserted.

May also be shown as 810109011002ffff or 0x810109011002ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

No action; information only.

764

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды