Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 797

Страница: 797 / 1222

Alert Category

Critical - Power

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

•

8107020d-2b81ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (FDIMM Endurance)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 8107020d2b81ffff or 0x8107020d2b81ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only. FDIMM Warranty :

•

8107020f-2201ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (TXT ACM Module)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 8107020f2201ffff or 0x8107020f2201ffff

Severity

Info

Serviceable

Appendix A. Integrated management module II (IMM2) error messages

785

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды