Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 219 | Manualshive

Страница: 219 / 1222

background image

Table 24. Components associated with power rail errors

Pwr rail error in the IMM event log

Components

Pwr rail A error

• Microprocessor 1

Pwr rail B error

• Microprocessor 2

Pwr rail C error

• Optional adapter (if one is installed) in PCI riser-card

assembly 1

• PCI riser-card assembly 1

• Fan 1

• DIMMs 1 through 6

Pwr rail D error

• Optional dual-port network adaptor

• Fan 2

• DIMMs 7 through 12

Pwr rail E error

• Optional DVD drive (if one is installed)

• Hard disk drives

• DIMMs 13 through 18

Pwr rail F error

• Optional adapter (if one is installed) in PCI riser-card

assembly 1

• PCI riser-card assembly 1

• Fan 4

• DIMMs 19 through 24

Pwr rail G error

• Optional PCI adaptor power cable (if one is present)

• Fan 3

• Hard disk drives

• Hard disk drive backplane assembly

Pwr rail H error

• Optional PCI adaptor power cable (if one is present)

• Optional adapter (if one is presented) installed in PCI

riser-card assembly 2

• PCI riser-card assembly 2

d.

Replace the identified component.

Step 5.

Remove the adapters and disconnect the cables and power cords to all internal and external
devices until the server is at the minimum configuration that is required for the server to start (see
“Power-supply LEDs” on page 179 for the minimum configuration).

Step 6.

Reconnect all ac power cords and turn on the server. If the server starts successfully, reseat the
adapters and devices one at a time until the problem is isolated.

If the server does not start from the minimum configuration, see “Power-supply LEDs” on page 179 to
replace the components in the minimum configuration one at a time until the problem is isolated.

Solving Ethernet controller problems

The method that you use to test the Ethernet controller depends on which operating system you are using.
See the operating-system documentation for information about Ethernet controllers, and see the Ethernet
controller device-driver readme file.

Try the following procedures:

Troubleshooting

207

«
...
217
218
219
220
221
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3650 M4 BD 5466

imagePRESS Server G200

Бренд: Canon Страницы: 82

Бренд: Canon Страницы: 88

Бренд: IBM Страницы: 908

Бренд: Aaeon Страницы: 38

N2400 - TaskSmart - 1 GB RAM

Бренд: Compaq Страницы: 372

Бренд: Buffalo Страницы: 2

Бренд: Nortel Страницы: 144

Бренд: EMC Страницы: 34

Бренд: Synology Страницы: 24

8668 - Eserver xSeries 232

Бренд: IBM Страницы: 182

SuperServer 5013G-M

Бренд: Supero Страницы: 104

Бренд: Fujitsu Страницы: 200

PRIMERGY TX140 S2

Бренд: Fujitsu Страницы: 86

PRIMERGY TX150 S3

Бренд: Fujitsu Страницы: 95

PRIMERGY TX150 S6

Бренд: Fujitsu Страницы: 118

Бренд: Fujitsu Страницы: 305

PRIMERGY TX150 S6

Бренд: Fujitsu Страницы: 127

PRIMERGY TX140 S2

Бренд: Fujitsu Страницы: 332

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды