Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 1026

Страница: 1026 / 1222

3. If error persists, or boot is unsuccessful, (Trained service technician only) Replace the system

board.

•

I.3818003 [I.3818003] The CRTM flash driver could not lock the secure flash region.

Explanation:

CRTM Could not lock secure flash region

Severity

Info

User Response

Complete the following steps:

1. If system failed to boot successfully, DC cycle system.

2. If system boots to F1 setup, flash UEFI image and reset bank to primary (if required). If system

boots without error, recovery is complete and no additional action is required.

3. If system fails to boot, or if flash attempt fails, (Trained service technician only) Replace the

system board.

•

I.58015 [I.58015] Memory spare copy initiated.

Explanation:

Spare Copy Started

Severity

Info

User Response

Complete the following steps:

1. No user required for this event. This is for informational purposes only.

•

I.580A4 [I.580A4] Memory population change detected.

Explanation:

DIMM Population Change Detected

Severity

Info

User Response

Complete the following steps:

1. Check system event log for uncorrected DIMM failures and replace those DIMMs.

•

I.580A5 [I.580A5] Mirror Fail-over complete. DIMM number % has failed over to to the mirrored

copy.

Explanation:

DIMM Mirror Fail-over Detected

Severity

Info

User Response

Complete the following steps:

1. Check the system-event log for uncorrected DIMM failures and replace those DIMMs.

1014

Lenovo System x3650 M4 Installation and Service Guide

«
...
1024
1025
1026
1027
1028
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды