Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 1117

Страница: 1117 / 1222

–

Latest level of BMC/IMM

•

201-827-000 : Standalone Memory Test Aborted

BIOS: ECC function has been disabled by BIOS. Go to Setup and enable ECC generation.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-827-001 : Standalone Memory Test Aborted

BIOS: ECC function has been disabled by BIOS. Go to Setup and enable ECC generation.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Appendix C. DSA diagnostic test results

1105

«
...
1115
1116
1117
1118
1119
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды