Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 372

Страница: 372 / 1222

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0011

User Response

Information only; no action is required.

•

4000000c-00000000 : OS Watchdog response [arg1] by [arg2] .

This message is for the use case where an OS Watchdog has been enabled or disabled by a user.

May also be shown as 4000000c00000000 or 0x4000000c00000000

Severity

Warning

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0012

User Response

Information only; no action is required.

•

4000000d-00000000 : DHCP[[arg1]] failure, no IP address assigned.

This message is for the use case where a DHCP server fails to assign an IP address to a Management
Controller.

May also be shown as 4000000d00000000 or 0x4000000d00000000

Severity

Warning

360

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды