Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 700

Страница: 700 / 1222

•

806f070c-2001ffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 1)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c2001ffff or 0x806f070c2001ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0126

User Response

Make sure that DIMMs are installed in the correct sequence and have the same size, type, speed,
and technology.

•

806f070c-2002ffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 2)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c2002ffff or 0x806f070c2002ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0126

User Response

688

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды