Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 1193

Страница: 1193 / 1222

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-907-001 : IMM I2C Test Failed

IMM Indicates failure in Ambient Temperature Sensor bus (BUS 6).

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-908-001 : IMM I2C Test Failed

IMM Indicates failure in PCA9557 IO Expander bus (BUS 7).

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

3. Run the test again.

Appendix C. DSA diagnostic test results

1181

«
...
1191
1192
1193
1194
1195
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды