Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 276

Страница: 276 / 1222

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords.

Step 3.

Remove the server cover (see “Removing the cover” on page 240).

Step 4.

Open the tape drive tray release latch and slide the drive tray out of the bay approximately 25
mm (1 inch).

Step 5.

Disconnect the power and signal cables from the rear of the tape drive.

Step 6.

Pull the drive completely out of the bay.

000

Figure 180. Tape drive removal

Step 7.

Remove the tape drive from the drive tray by removing the four screws on the sides of the tray.

Figure 181. Screws removal

Step 8.

If you are not installing another drive in the bay, insert the tape drive filler panel into the empty
tape drive bay.

Step 9.

If you are instructed to return the drive, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

264

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды