Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 791

Страница: 791 / 1222

Prefix:

PLAT

ID:

0509

User Response

No action; information only. SMM Monitor :

•

8105010d-2b81ffff : Sensor [SensorElementName] has indicated limit no longer exceeded. (FDIMM

TempLimit)

This message is for the use case when an implementation has detected a Sensor limit is no longer
exceeded.

May also be shown as 8105010d2b81ffff or 0x8105010d2b81ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0513

User Response

No action; information only.

•

81070101-0c01ffff : Sensor [SensorElementName] has deasserted the transition from normal to

non-critical state. (Ambient Status)

This message is for the use case when an implementation has detected that a Sensor has deasserted a
transition to non-critical from normal.

May also be shown as 810701010c01ffff or 0x810701010c01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Temperature

SNMP Trap ID

Appendix A. Integrated management module II (IMM2) error messages

779

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды