Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 148

Страница: 148 / 1222

Figure 132. Syringe

Step 6.

Install the heat sink onto the microprocessor. See “Replacing a microprocessor and heat sink” on
page 330.

Completing the installation

Use this information to complete the installation.

To complete the installation, complete the following steps:

Step 1.

If you removed the air baffle, reinstall it (see “Replacing the air baffle” on page 136).

Step 2.

If you removed either of the PCI riser-card assemblies, replace the riser-card assemblies (see
“Installing a PCI riser-card assembly” on page 137).

Step 3.

If you removed the server cover, replace it (see “Replacing the cover” on page 139).

Step 4.

Install the server in the rack cabinet (see the

Rack Installation Instructions

that come with the

server for instructions).

Step 5.

Reconnect the cables and power cords (see “Connecting the external cables” on page 139).

Step 6.

Update the server configuration (see “Updating the server configuration” on page 140).

Step 7.

Slide the server back into the rack, if necessary.

Step 8.

Start the server. Confirm that it starts correctly and recognizes the newly installed devices, and
make sure that no error LEDs are lit.

Step 9.

(Business Partners only) Complete the additional steps in “Instructions for Business Partners”
on page 25.

Replacing the air baffle

Use this information to replace the air baffle.

To replace the air baffle (if it has been removed), complete the following steps:

Figure 133. Air baffle installation

136

Lenovo System x3650 M4 Installation and Service Guide

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды