Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 1222

background image

00000000000

00000000000

Figure 136. Front view

0

000

000

000

000

000

00

000

000

000

000

000

00

0000

0000

00

00

000

000

000

000

000

000

0000000

0000000

0000000

0000000

0000000

0000000

0000000

0000000

0000000

0000000

0000000

0000000

Video Serial

Power supply 1

Power supply 2

Ethernet1
(shared system
management ethernet) Ethernet2

Ethernet3

Ethernet4

System-management
(ethernet)(dedicated)

10G ethernet
(with optional
10G ethernet card)

USB5

USB3 USB4

USB6

NMI
button

Figure 137. Rear view

You must turn off the server before you connect or disconnect cables.

See the documentation that comes with any external devices for additional cabling instructions. It might be
easier for you to route cables before you connect the devices to the server.

If the server comes with an installed operating system, see the documentation that comes with the operating
system for additional cabling instructions.

Updating the server configuration

Use this information to update the server configuration.

When you start the server for the first time after you add or remove a device, you might receive a message
that the configuration has changed. The Setup utility starts automatically so that you can save the new
configuration settings.

Some optional devices have device drivers that you must install. For information about installing device
drivers, see the documentation that comes with each device.

If the server has an optional RAID adapter and you have installed or removed a hard disk drive, see the
documentation that comes with the RAID adapter for information about reconfiguring the disk arrays.

If you have installed a USB hypervisor memory key on the SAS riser-card, see the user's guide that comes
with the hypervisor memory key. Hypervisor enables guest operating systems to function on the server.

For information about configuring the integrated Gigabit Ethernet controller, see “Configuring the Ethernet
controller” on page 155.

140

Lenovo System x3650 M4 Installation and Service Guide

«
...
150
151
152
153
154
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3650 M4 BD 5466

Express5800/T110g-S

Бренд: NEC Страницы: 34

Бренд: Xblue Networks Страницы: 148

Бренд: HPE Страницы: 174

Бренд: TerraMaster Страницы: 13

Бренд: Sun Oracle Страницы: 6

TotalStorageFAStT900

Бренд: IBM Страницы: 112

Бренд: Hitachi Страницы: 57

Бренд: Hitachi Страницы: 76

BladeSymphony 1000

Бренд: Hitachi Страницы: 52

Бренд: Hitachi Страницы: 91

Бренд: Hitachi Страницы: 174

HVM Navigator V03-06

Бренд: Hitachi Страницы: 312

NVM Navigator v03-07

Бренд: Hitachi Страницы: 316

Бренд: Hitachi Страницы: 129

Бренд: Hitachi Страницы: 466

Бренд: Hitachi Страницы: 530

SuperServer 2029BT-HNC0R

Бренд: Supermicro Страницы: 148

Бренд: Lenovo Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды