LC Packings Probot 161403 Скачать руководство пользователя страница 56

Страница: 56 / 118

Installation and Getting Started

2-36

D960R3

User’s Manual Probot

FIGURE 2-37 The Fractionation Application Wizard – Fraction Control Mode

The following modes are available:

•

Time

– The fractionation is controlled by time. The intervals are specified in

seconds and can be as low as 4 seconds. Time control is the most commonly

and safest control mode. This control mode allows also for fractionation by a

time table.

•

External

–Input signals control the fractionation (e.g. peak start and peak end).

A CHROMELEON program can be designed to generate to generate such

signals on the Ultimate Micropump while the UV signal is used for peak

detection. This allows for collecting of peaks only.

•

Manual

– This control mode requires input of the operator. The operator

determines by manual input (mouse) the when a peak starts or ends. This

requires that the operator monitors the entire chromatographic run and

provides the right signal with each peak.

Note: In time control mode the entire chromatogram is collected, e.g. all peaks

and ‘waste’. With external and manual control, the ‘waste’ can be discarded.
Make certain that the peak detection parameters are properly set to avoid the
possibility that peaks are treated as ‘waste’ in external control mode.

The next step is to specify the number of LC runs (injections) and to define in

which way the available sample carriers are used (e.g. one sample carrier per

injection or LC run). FIGURE 2-38 shows the three basic possibilities and which

option the appropriate is depending on the requirements:

•

One injection

- The LC run (‘sample’) is collected in one group. This group can

use all spots of all sample carriers.

•

Multiple injections, optimal use of spots

– Multiple LC runs are collected in one

large group. This group can use all spots of all sample carriers.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды