LC Packings Probot 161403 Скачать руководство пользователя страница 31

Страница: 31 / 118

Installation and Getting Started

User’s Manual Probot

D960R3

2-11

2.5

Software Installation

The following section describes the installation of the

Carrier Software, Version

2.0. Please refer to the ‘Readme’ file provided on the

Carrier CD ROM for

additional information and updated instructions.

2.5.1

System requirements

To run the

Carrier software, your personal computer must fulfill the following

minimal specifications:

•

PC with Intel Pentium II, Celeron, AMD ATHLON, DURON microprocessor or

compatible, min. 277 MHz.

•

64 MB main memory.

•

One CD ROM drive, a hard disk with at least 20 MB free storage capacity.

•

SVGA-graphics adapter (at least: 800x600 pixels, 32kByte colors).

•

Color monitor with appropriate resolution and color specifications.

•

Microsoft

Windows

XP (SP1 recommended), NT (Version 4.0 SR3, 5, 6),

Windows 2000.

•

Mouse (a mouse-wheel is recommended).

•

One free serial COM-port for the RS232-connection to the Probot Micro

Fraction Collector.

•

One free USB port for the connection of the video adapter (as part of the

optional camera).

2.5.2

Installation of

Carrier

To install the

Carrier software:

Put the

Carrier CD ROM into the CD ROM drive. If you have the Autostart

function of Windows activated, the setup program will start automatically. If

Autostart is not activated, use the Windows Explorer or the

Run

command

from the Windows Start menu to run SETUP.EXE on the CD ROM. All

necessary files are decompressed and copied to your computer.

Select which options you want to install. If your Probot includes the camera

option with the Belkin

VideoBusII, you can choose to unpack the required

drivers to a specified location on your hard disk.

Respond to each dialog box of the installation program as it is presented. If

you always choose the

Next

button, the µCarrier software will be installed in

the default folder (e.g.

C:\Program Files\LCP\uCarrier

If you have chosen to copy the Belkin drivers to your PC, the installation

software will tell you at some point to connect the Belkin video adapter.

Windows will automatically start the ‘New hardware found’ wizard. Enter the

location where the wizard finds the drivers installed in step b). Refer to

APPENDIX E for more details about the installation and usage of the video

adapter.

After installation is completed, restart your computer.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды