LC Packings Probot 161403 Скачать руководство пользователя страница 26

Страница: 26 / 118

Installation and Getting Started

2-6

D960R3

User’s Manual Probot

2.4

Installing the Probot with the UltiMate Capillary HPLC System

The following section describes how to install the Probot Micro Fraction Collector

as a component in the LC Packings UltiMate Capillary HPLC system.

2.4.1

Electrical Connections

The Probot Micro Fraction Collector is controlled by the

Carrier

™

software

package using a serial communication port of the personal computer (PC). In

addition, the Probot can be controlled by external events (e.g. START, TTL IN).

A manual control unit can be connected which allows for manual movement of

all three axes.

All electrical connections are made on the rear panel of the instrument

(FIGURE 1-4).

CAUTION

Caution: Avoid touching the electrical contacts on the terminal strips.

Electrostatic discharges could damage internal components. The manufacturer
will not accept any liability for damages directly or indirectly caused by
connecting the Probot Micro Fraction Collector to instruments which do not meet

relevant safety standards.

2.4.1 A

RS-232 Connector

Connect the RS-232 cable to the RS-232 connector on the Probot and to the

COM port of the personal computer.

TABLE 2-1

The Probot RS-232 Communication Cable

Probot (9-pin male)

PC (9-pin female)

Description

2 3 TxD
3 2 RxD
5 5 Ground
7 7 Reset

2.4.1 B

START Connector

If the external start feature is used, connect the Start Cable to the START

connector on the Probot and to the device that will provide the start signal for

the Probot (e.g. a TTL output of the UltiMate Micropump or a relay output of the

FAMOS).

TABLE 2-2

The START Cable

Input

Pin No.

Color Code

Description

Start 7

lilac

Start

input

Ground 9

black

Ground

connection

CAUTION

Caution: If the controlling device does not use a switch or relay contacts, make

certain that the polarity is correct (e.g. connect the ground pin of the Probot to

the ground pin of the controlling device). The output signal of the controlling
device must be TTL level compatible.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды