LC Packings Probot 161403 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 118

background image

Warranty

viii

D960R3

User’s Manual Probot

Liability

Under no circumstances shall LC Packings be liable for damage to persons or
property. This warranty is the only warranty given by LC Packings with respect
to products and software provided with the products and is given in lieu of all

other warranties, express or implied, including, without limitation, any warranty
of merchantability or fitness for a particular purpose.

Your exclusive remedies and LC Packings’s sole liability for any non-conformity
or defect in the products and such software will be those expressed herein.

Under no circumstances will LC Packings’s liability arising from the performance
or failure to perform of any product or software, in contract, in tort (including
negligence), or otherwise, exceed the purchase price of the product and

software. In no event will LC Packings be liable, in contract, in tort (including
negligence), or otherwise for special, incidental, consequential or analogous
damages, including, without limitation, damages resulting from loss of use, loss
of profits, loss of business or loss of goodwill, even if LC Packings has been

advised of the possibility of such damages.

This warranty comprises the entire warranty between LC Packings and the
customer. It overrides any warranty related language that may appear in the

customer purchase order or other documentation provided by the customer.

This warranty shall be governed by, and construed and enforced in accordance
with, the laws of the Netherlands. It is non-transferable and shall run to the
benefit of the original purchaser only. Any change, alteration or amendment to

this warranty is not valid unless it has been approved in writing by an officer of
LC Packings.

North America

Europe and Asia

LC Packings / Dionex

LC Packings (Netherlands) BV

A Dionex Company

500 Mercury Drive

Abberdaan 114

Sunnyvale, CA 94088-3603

1046 AA Amsterdam

USA The

Netherlands

Technical Call Center

Phone: + 31 20 683 9768

USA/CA: (800) 346-6390

Fax:

+ 31 20 685 3452

«
...
6
7
8
9
10
...
»

Содержание Probot 161403























































































































Отзывы:

Нет отзывов

Похожие инструкции для Probot 161403

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: YATEK Страницы: 72

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Бренд: P.Lindberg Страницы: 76

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренд: Zero 88 Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды