LC Packings Probot 161403 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 118

background image

User’s Manual Probot

D960R3

xi

Warnings

The Danger sign, Warning sign and the Caution sign shown below are included in
various locations in this manual. These signs provide the following information:

DANGER

Danger: The information in a danger statement relates to a procedure, practice

condition or action that if not done correctly or adhered to could lead to personal

injury or loss of life.

WARNING

Warning: The information in a warning statement relates to a procedure, practice

condition or action that if not done correctly or adhered to could lead to severe
injury and/or damage or destruction to parts or all of the equipment.

CAUTION

Caution: The information in a caution statement relates to a condition that could

lead to damage to equipment and/or lead to invalid analytical results.

Note: The information in a note statement relates to important information that

should be read and understood before continuing.

Safety Precautions

Note: The following precautions should be followed to minimize the possibility of

personal injury and/or damage to property.

Note: Make certain that you are familiar with the contents of this manual before

working on the system.

The Probot Micro Fraction Collector is typically incorporated into an LC/MS
system. The user should follow all safety precautions, warnings, etc provided by
the manufacturer of the system(s), in addition note the items presented below:

1)

Install the system in a well-ventilated laboratory. If the mobile phase includes

volatile or flammable solvents, make certain that they are not allowed to
enter the workspace.

2)

If the mobile phase includes volatile or flammable solvents, avoid open

flames and sparks.

«
...
9
10
11
12
13
...
»

Содержание Probot 161403























































































































Отзывы:

Нет отзывов

Похожие инструкции для Probot 161403

Бренд: ABB Страницы: 86

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: YOKOGAWA Страницы: 75

QUICK-ALIGN Vari-Flex

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 2

Бренд: Össur Страницы: 8

Бренд: Rigol Страницы: 12

Pro hunter 2525

Бренд: SprotDog Страницы: 28

Бренд: Barikell Страницы: 32

Бренд: Carbatec Страницы: 29

Бренд: PurAthletics Страницы: 2

Бренд: Lightolier Страницы: 2

OMNIS 2.1006.0010

Бренд: Metrohm Страницы: 34

Бренд: Seiler Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды