LC Packings Probot 161403 Скачать руководство пользователя страница 117

Страница: 117 / 118

Appendix E

User’s Manual Probot

D960R3

E-5

E.2.4

Troubleshooting

If no video image is visible, check the correct settings of µCarrier first. If the

settings appear correct, check to see if the Belkin VideoBusII device is installed

properly.

To check the µCarrier settings:

Start

Carrier 2.0, select the

View

menu from the tool bar and choose

Show

video camera window

to open the video window (FIGURE E-4).

FIGURE E-4

The Video Camera Window of µCarrier

Press the

On/Off

button to display the camera image.

Use the

Source

button to select ‘Belkin VideoBusII’ as the capture device. If

the Belkin VideoBusII is the only capture device this setting should be ‘0’.

Restart the

Carrier software and check if all settings are properly.

In order to check the installation of the Belkin VideoBusII device:

Open the ‘Control Panel’ via the

Start

button from the Windows Tool Bar.

Open

System

and select the

Hardware

tab from the

System Properties

window, and then choose the

Device Manager

Click on the plus sign next to ‘Imaging Devices’. Under this heading you

should see ‘Belkin USB VideoBus II, Video’. This would be the video capture

option that you would choose in your application.

Click on the plus sign next to ‘Sound, video and game controllers’. Here you

should see ‘Belkin USB VideoBus II, Audio’. This would be the sound

capture option that you would choose in your application.

If you do not see either of these or if there is an unknown or USB device

with a question or exclamation mark, proceed to the un-installation

instructions (Section E.3).

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды