LC Packings Probot 161403 Скачать руководство пользователя страница 54

Страница: 54 / 118

Installation and Getting Started

2-34

D960R3

User’s Manual Probot

2.8.4

Create a New Application using the Wizard

Depending on the requirements and complexity of a specific application, various

parameters need to be defined to achieve the best performance. This can make it

difficult for even an experienced user to get started. However, the most common

application is a time controlled fractionation task, which requires only a few

parameters to run it successfully on the Probot.

µCarrier offers the

Fractionation Application Wizard

to assist you in creating such

an application. This section explains how to use the

Fractionation Application

Wizard

on a step by step basis.

The application presented in this section is based on the ‘Advanced fractionation

task’. If a ‘Basic fractionation task’ is required, please use the application editor

to modify one of the predefined applications.

Note: The figures (screenshots) provided below may vary depending on the

choices made in the wizard. For this example, the most general choices were
selected.

Switch to the

Application Editor

by selecting the

ApplicationEditor

icon.

Select the

New

button to start the wizard.

The

Confirm

message box is presented. Choose

Yes

(FIGURE 2-34) if you are

willing to lose any unsaved data. If you want to keep the existing tray and

tasks setup, quit with

Cancel

and start the wizard from the

File

(

New/Application

FIGURE 2-34 Confirm Discarding the Tray and Tasks

The

Fractionation Application Wizard

is presented (FIGURE 2-35). Select a

‘Load a tray from a file’ option and confirm with the

Next

button.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды