LC Packings Probot 161403 Скачать руководство пользователя страница 105

Страница: 105 / 118

Appendix D

User’s Manual Probot

D960R3

D-3

D.3

Setting up the Probot

The following sections describe the steps that are needed to setup and to adjust

the Probot to use the vacuum waste removal option successfully.

D.3.1

Electrical Connections

The START input is used to start the µCarrier application while the TTL1 input

(‘Peak start’) and TTL2 input (‘Peak end’) is used to control the fractionation.

The lift magnet is controlled by a µCarrier ‘switch task’ and does not require a

control input.

To control Probot by the relay outputs of the UltiMate Micropump, connect the

START and TTL inputs (Section 2.4.1 D) of the Probot as presented in

TABLE D-2. Use the cables and connectors which are provided with the Probot

and the UltiMate system.

TABLE D-2

Connecting the Probot and the Micropump

Probot

Color Code

UltiMate Micropump EVENTS

Start

Signal

Start

Lilac

Event 3, pin 3

Ground

Black

Ground, pin 4

TTL Inputs (TT1=Peak Start, TTL2=Peak End)

TTL1, pin 1

Red

Event 7, pin 7

TTL2, pin 3

Orange

Event 8, pin 9

Ground, pins 9,11,13,15

Blue

Event 7 and 8, pins 8, 10

Note: If you are using a TTL output (e.g. of the UltiMate Micropump), the control

logic will be inverted (e.g. an inactive output of the Micropump will be recognized
as an active input by the Probot).

D.3.2

Connecting the Vacuum Pump

Connect the vacuum pump and the Waste container to the Probot vacuum port

as presented in FIGURE D-3.

Vacuum Pump

Tubing

Probot Tubing

Vacuum Pump

Probot Vacuum

Port

Waste Container

FIGURE D-3 Connecting the Vacuum Pump

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды