LC Packings Probot 161403 Скачать руководство пользователя страница 34

Страница: 34 / 118

Installation and Getting Started

2-14

D960R3

User’s Manual Probot

2.6.5

The Main Toolbar

The main toolbar (FIGURE 2-7), which is presented in the upper left of the main

window of µCarrier (FIGURE 2-10) presents several buttons:

FIGURE 2-7 The Main Toolbar

Removes the tray and all tasks in the task list and starts the

wizard corresponding to the editor which is currently active.

This button shows or hide the browser pane on the left and

enables or disables easy file access.

Opens an existing sample carrier, tray table or application file.

The sample carrier files have the extension ‘.rck’, the tray files

have the extension ‘.try’ and the application files have the

extension ‘.app.’

Saves a (new) sample carrier, a tray table or an application.

Activates the

Sample Carrier Editor

to create new or modify

existing sample carriers.

Activates the

Tray Editor

to create new or modify existing trays.

Tray layout and spot grouping is available in this editor.

Activates the

Application Editor

to create new or modify

existing applications. Grouping of sample carrier spots is also

available.

Activates

Manual Device Control

to control the Probot table and

dosage module manually.

Opens the manual control panel of the robot drive.

Runs the application

Pauses the application (only active during run)

Aborts the application (only active during run)

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды