LC Packings Probot 161403 Скачать руководство пользователя страница 62

Страница: 62 / 118

Installation and Getting Started

2-42

D960R3

User’s Manual Probot

FIGURE 2-44 The Fractionation Application Wizard – Completed

The last screen of the wizard (FIGURE 2-44) offers three options.

•

Align the sample carriers

– Select this option if no alignment was performed

with the sample carriers before. Proper alignment is essential!

•

Start (Run) the application

– Select this option if the sample carriers were

already aligned, the application can run immediately.

•

Exit wizard

– allows you to review the application in the

Application Editor

and

to make modifications, if required.

Select one of the options and choose

Next

to save the application and to

finish the wizard.

Note: It is recommended to review the application before running it.

After exiting the wizard the

Application Editor

(FIGURE 2-45) is automatically

opened with the application defined above.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды