LC Packings Probot 161403 Скачать руководство пользователя страница 70

Страница: 70 / 118

Maintenance and Troubleshooting

3-2

D960R3

User’s Manual Probot

3.2

Maintenance

Maintenance refers to a variety of activities that should be performed on a

routine basis to optimize performance of the system. Many routine maintenance

activities can be readily performed by the user.

In some cases (e.g. replacement of critical components), we recommend that a

factory trained service engineer should be called to perform the operation. This

will ensure optimal long term performance and maximum uptime. LC Packings

provides a broad range of service support activities to ensure that the Probot

Micro Fraction Collector is functioning in a suitable manner. These activities can

be customized to meet the specific needs of the customer. For further

information, please contact your local LC Packings office or representative.

TABLE 3-1

Recommended Maintenance Schedule

Frequency

Operation

Before operating, check for any air bubbles in

the fluidic lines and degas the wash solvent.
Check that there are no leaks of the fluidics

connections.
Check that salts are not deposited by the

fluidics joints or the needle.

Every Day

When using buffer solutions, flush the system

thoroughly after use with a solvent that does

not contain buffers/salts.

Every 3 months

Inspect the condition of all tubing (cracks, nicks,

cuts, clogging).
Check:
Rotary valve
Syringe

Every 6 months

Replacing the Syringe/Syringe tip

Every year

Inspection, cleaning and lubrication of all

spindles (

contact LC Packings

Note: The frequency of the various activities described above is a good starting

point. As the user gains experience with the system, it will be found that some

activities can be done less frequently and other need to be done more frequently.
The frequency is dependent on a number of factors including the nature of the
sample and the mobile phase.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды