LC Packings Probot 161403 Скачать руководство пользователя страница 103

Страница: 103 / 118

User’s Manual Probot

D960R3

D-1

APPENDIX D

The Vacuum Waste Removal
Option

D.1

Overview

This appendix describes the features and usage of the Vacuum Waste Removal

option. This option is provided as a factory installed option only. If your Probot

Micro Fraction Collector does not include this option, contact your local

representative or LC Packings for upgrade information.

The vacuum waste removal option allows the user to remove undesired portions

of the separation (‘waste’) without the need to spot them onto the target. A

vacuum that can be applied draws then the solvent into a waste container.

The vacuum waste removal option includes the following items:

•

Lift magnet

•

Vacuum pump

•

Waste container

•

Tubing and vacuum connectors

To control the vacuum waste removal, event outputs of the UltiMate capillary

HPLC system are used in combination with the peak detection capability of
CHROMELEON

(see also APPENDIX B).

The following sections provide information about how to install the vacuum

waste removal option and show how to setup the µCarrier and the

CHROMELEON software to control the waste removal option of the Probot. All

information provided refers to µCarrier version 2.0 and to CHROMELEON

6.5

SP3.

Note: The Vacuum Waste Removal Option can not be used in conjunction with

the dosage module (e.g. no matrix solution can be added).

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды