Keysight DSOX3012T Скачать руководство пользователя страница 323

Страница: 323 / 530

Save/Email/Recall (Setups, Screens, Data)

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

323

•

Mask (*.msk)

— This creates a mask file in a Keysight proprietary format that

can be read by Keysight InfiniiVision oscilloscopes. A mask data file includes

some oscilloscope setup information, but not all setup information. To save

all setup information including the mask data file, choose "Setup (*.scp)"

format instead. See

“To save masks"

on page 328.

•

Arbitrary Waveform data (*.csv)

— This creates a file of comma-separated

values for the arbitrary waveform points' time and voltage values. See

“To

save arbitrary waveforms"

on page 328.

•

Analysis Results (*.csv)

— A file of comma-separated values is saved for the

analysis types selected using the

Analysis Select

softkey.

•

Current Harmonics data (*.csv)

Power Supply Rejection Ration (PSRR) data (*.csv)

Control Loop Response (Bode) data (*.csv)

— When the DSOX3PWR power

analysis application is licensed, these options create a file of

comma-separated values for the different types of analysis results. See the

PWR Power Measurement Application User's Guide

for more information.

•

Frequency Response Analysis data (*.csv)

— This creates a file of

comma-separated values for the Frequency Response Analysis results table

values. In the saved file, there are three data columns: frequency (Hz), gain

(dB), and phase (degrees). See

“To view and save the analysis results"

page 298.

You can also configure the

[Quick Action]

key to save setups, screen images, or

data. See

“Configuring the [Quick Action] Key"

on page 357.

To save setup files

Setup files can be saved to one of 10 internal (\User Files) locations or to an

external USB storage device.

Press

[Save/Recall] > Save > Format

; then, turn the Entry knob to select

Setup

(*.scp)

Press the softkey in the second position and use the Entry knob to navigate to

the save location. See

“To navigate storage locations"

on page 329.

Finally, press the

Press to Save

softkey.

A message indicating whether the save was successful is displayed.

Setup files have the extension SCP. These extensions appear when using the File

Explorer (see

“File Explorer"

on page 344), but they do not appear when using the

Recall Menu.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды