Keysight DSOX3012T Скачать руководство пользователя страница 179

Страница: 179 / 530

Triggers

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

179

The time values for the selected qualifier are set using the qualifier time set

softkeys (

and

) and the Entry knob.

To set the analog or digital channel patterns, press the

Analog

softkey or the

Digital

softkey and use the binary keypad dialog to enter:

•

sets the pattern to zero (low) on the selected channel. A low is a voltage

level that is less than the channel's trigger level or threshold level.

•

sets the pattern to 1 (high) on the selected channel. A high is a voltage

level that is greater than the channel's trigger level or threshold level.

•

sets the pattern to don't care on the selected channel. Any channel set to

don't care is ignored and is not used as part of the pattern. However, if all

channels in the pattern are set to don't care, the oscilloscope will not trigger.

•

The rising edge ( ) or falling edge ( ) softkey sets the pattern to an edge

on the selected channel. Only one rising or falling edge can be specified in

the pattern. When an edge is specified, the oscilloscope will trigger at the

edge specified if the pattern set for the other channels is true.

If no edge is specified, the oscilloscope will trigger on the last edge that

makes the pattern true.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды