Keysight DSOX3012T Скачать руководство пользователя страница 248

Страница: 248 / 530

248

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Measurements

Power App

Measurements

Note that additional Power App measurements are available when the

DSOX3PWR power measurement and analysis license is installed and the Power

Application is enabled. For more information, see the

PWR Power Measurement

Application User's Guide

www.keysight.com/find/3000TX-Series-manual

or on

the Documentation CD.

Dual-Channel

(N2820A Probe)

Measurements

Note that additional measurements are available with the N2820A high-sensitivity

current probe when both the Primary and Secondary probe cables are used.

Zoom In waveform data below the probe's clamp level is joined with Zoom Out

waveform data above the probe's clamp level to create the waveform on which the

measurement is made. These measurements are only valid for analog input

channels.

Measures between two sources.

Press

Settings

to specify the second

source.

Yes

Yes

Yes

The resultant units are in Hertz.

“X at Min Y"

on page 264

Yes

The resultant units are in Hertz.

Use the cursors to make other measurements on FFT.

Measurement

Valid

for

Math

FFT

Valid for

Digital

Channels

Notes

Dual-Channel (N2820A Probe)

Measurement

Notes

Amplitude

See

“Amplitude"

on page 251.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды