Keysight DSOX3012T Скачать руководство пользователя страница 379

Страница: 379 / 530

Reference

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

379

Licensed Options Available

The following licensed options can be easily installed without returning the

oscilloscope to a Service Center. See data sheets for details.

Table 5

Licensed Options Available

License

Description

Upgrade model number, notes

AERO

MIL-STD-1553 and ARINC 429 Serial Triggering and Analysis.

Order DSOX3AERO.

AUDIO

Audio Serial Triggering and Analysis (I2S).

Order DSOX3AUDIO.

AUTO

Automotive Serial Triggering and Analysis (CAN,LIN).

Order DSOXT3AUTO.

CANFD

Automotive Serial Triggering and Analysis (CAN,LIN).

Order DSOXT3AUTO.

COMP

Computer Serial Triggering and Analysis

(RS232/422/485/UART).
Provides trigger and decode capability for many UART

(Universal Asynchronous Receiver/Transmitter) protocols

including RS232 (Recommended Standard 232).

Order DSOX3COMP.

CXPI

CXPI (Clock Extension Peripheral Interface) Serial Triggering

and Analysis.

Order DSOXT3CXPI.

EMBD

Embedded Serial Triggering and Analysis (I2C, SPI).

Order DSOX3EMBD.

FLEX

FlexRay Triggering and Analysis.

Order DSOX3FLEX.

FRA

Frequency Response Analysis.

Order DSOXT3FRA.

MASK

Mask Limit Test
Lets you create a mask and test waveforms to determine

whether they comply to the mask.

Order DSOX3MASK.

memMax

Memory Upgrade.
It shows the total memory depth (4 Mpts interleaved).

Order DSOX3MEMUP.

MSO

Mixed Signal Oscilloscope (MSO). Upgrade a DSO to an MSO.
Adds 16 digital channels. You do not have to install any

hardware.

Order DSOXT3MSO.
The digital probe cable kit is supplied with

the MSO license.

NFC

Near Field Communication (NFC) Trigger.

Order DSOXT3NFC.

NRZ

Manchester/NRZ (Non Return to Zero) Triggering and

Analysis.

Order DSOX3NRZ.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды