Keysight DSOX3012T Скачать руководство пользователя страница 500

Страница: 500 / 530

500

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

SENT Triggering and Serial Decode

Slow Channel Serial Messages are always displayed as defined by the SENT

specification.

Press the

Display

softkey to select between hexadecimal, unsigned decimal,

or "transfer function" display of Fast Channel nibbles, signals, and CRC

values, as well as Slow Channel IDs, data, and CRC values. (The S&C value is

always displayed in binary.)

Your selection is used for both the Lister and the decode line displays.

When

Transfer Function

is selected (for message formats that include fast

signals), Fast Channel Signals display a calculated physical value based on

the specified

Multiplier

and

Offset

(under the

Fast Signals

softkey):

•

PhysicalValue = (Multiplier * SignalValueAsUnsignedInteger) + Offset

When

Transfer Function

is selected, the CRC and Slow Channel information is

displayed in hex.

When a fast signals message decode/triggering is selected, press the

Fast

Signals

softkey to open the SENT Signals Menu where you can define and

specify the display of up to six Fast Signals.

NOTE

For the Slow Channel, the proper format, Short or Enhanced, must be chosen for proper

decoding and triggering to occur.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды