Keysight DSOX3012T Скачать руководство пользователя страница 484

Страница: 484 / 530

484

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

MIL-STD-1553/ARINC 429 Triggering and Serial Decode

•

Parity Error

— triggers if the (odd) parity bit is incorrect for the data in the

word.

•

Sync Error

— triggers if an invalid Sync pulse is found.

•

Manchester Error

— triggers if a Manchester encoding error is detected.

MIL-STD-1553 Serial Decode

To set up the oscilloscope to capture MIL-STD-1553 signals, see

“Setup for

MIL-STD-1553 Signals"

on page 481.

To set up MIL-STD-1553 serial decode:

Press

[Serial]

to display the Serial Decode Menu.

Use the

Base

softkey to select between hexadecimal and binary display of the

decoded data.

The base setting is used for the display of the remote terminal address and the

data, in both the decode line and in the Lister.

If the decode line does not appear on the display, press the

[Serial]

key to turn it

on.

If the oscilloscope is stopped, press the

[Run/Stop]

key to acquire and decode

data.

You can use the horizontal

Zoom

window for easier navigation of the decoded data.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды