Keysight DSOX3012T Скачать руководство пользователя страница 297

Страница: 297 / 530

Frequency Response Analysis

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

297

There are settings for:

•

The start and stop frequencies in the sweep, as well as the number of points

per decade.

•

The channels probing the input and output. (Click the help icon to view a

connection diagram.)

•

The waveform generator amplitude and expected output load impedance.

To specify different amplitudes for different decades, select

Amplitude Profile

The output impedance of the Gen Out signal is fixed at 50 ohms. However,

the output load selection lets the waveform generator display the correct

amplitude and offset levels for the expected output load. If the actual load

impedance is different than the selected value, the displayed amplitude and

offset levels will be incorrect.

Click the

Run Analysis

softkey.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды