manualshive.com logo in svg

Keysight DSOX3012T, Руководство пользователя

Keysight DSOX3012T - мощный осциллограф с функциональностью отличного качества. Пользовательская инструкция доступна для бесплатного скачивания на manualshive.com. Используйте этот ресурс для получения подробной информации о продукте и его функциях. Идеальный инструмент для профессиональных и любительских проектов.

Поделиться
Скачать
background image

SENT Triggering and Serial Decode

32

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

503

 

•

Successive Sync Pulses Error

 — triggers on a sync pulse whose width varies 

from the previous sync pulse's width by greater than 1/64 (1.5625%, as 

defined in the SENT specification).

4

If you choose the 

Fast Channel SC & Data

 trigger condition:

a

Press the 

Base

 softkey to choose between Hex or Binary data value entry.

Use the Binary method if you need to enter "don't care" bits (X) within a 

nibble. If all bits in a nibble are "don't care", the hex nibble is displayed as 

"don't care" (X). When all bits in a nibble are 1s or 0s, the hex value is shown. 

Hex nibbles that contain a mix of 0/1 bits and "don't care" bits are displayed 

as "$".

b

Press the 

SC & Data

 softkey and use the keypad dialog to enter the data 

value.

The S&C nibble is the left most nibble entered in the string of numbers, 

followed by the data nibbles.

5

If you choose the 

Slow Channel Message ID

 or 

Slow Channel Message ID & Data

 

trigger condition:

a

Press the 

Configuration

 softkey to select the desired packet ID for the selected 

packet type.

When an Enhanced Serial message format is specified (see 

“Setup for SENT 

Signals"

on page 497), press this softkey to select which enhanced format 

configuration is being used:

•

16-Bit Data, 4-Bit ID

•

12-Bit Data, 8-Bit ID

b

Press the 

Slow Message ID

 softkey and use the Entry knob (or press the 

softkey again and use a keypad dialog) to specify the Slow Message ID.

c

If you choose the 

Slow Channel Message ID & Data

 trigger condition, press the 

Slow Data

 softkey and use the Entry knob (or press the softkey again and use 

a keypad dialog) to specify the Slow Message data.

6

If you choose the 

Tolerance Violation

 trigger condition, press the 

Tolerance

 

softkey and use the Entry knob (or press the softkey again and use a keypad 

dialog) to specify the tolerance variation that is considered a violation.

The percentage entered must be less than the percent tolerance specified in 

the decode bus configuration settings.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSOX3012T

Malmet Drying Cabinet Operation, Maintenance And Installation Manual preview
Drying Cabinet
Бренд: Malmet Страницы: 14
Zempire EVO Series Pitching Instructions preview
EVO Series
Бренд: Zempire Страницы: 2
Össur i-limb access hand Instructions For Use Manual preview
i-limb access hand
Бренд: Össur Страницы: 246
Össur PROPRIO FOOT PSX01 Instructions For Use Manual preview
PROPRIO FOOT PSX01
Бренд: Össur Страницы: 374
ZIEHL-ABEGG ZA top SM315.100A Original Operating Instructions preview
ZA top SM315.100A
Бренд: ZIEHL-ABEGG Страницы: 76
Parker F12-152 Series Service Manual preview
F12-152 Series
Бренд: Parker Страницы: 24
Yetter TITAN 2967-033A Operator'S Manual preview
TITAN 2967-033A
Бренд: Yetter Страницы: 20
B&G RAM T0 User Manual preview
RAM T0
Бренд: B&G Страницы: 16
Orliman 94231 Use And Maintenance Instructions preview
94231
Бренд: Orliman Страницы: 11
American DJ DJ Scan/RG User Instructions preview
DJ Scan/RG
Бренд: American DJ Страницы: 8
COURANT M-DROP Manual preview
M-DROP
Бренд: COURANT Страницы: 2
laerdal AED LittleAnne Directions For Use Manual preview
AED LittleAnne
Бренд: laerdal Страницы: 64
Buyers 8891102 Installation Instructions preview
8891102
Бренд: Buyers Страницы: 2
Drive 10274 Assembly Instructions preview
10274
Бренд: Drive Страницы: 2
TECALEMIT DE 7288/2005 Installation Operation & Maintenance preview
DE 7288/2005
Бренд: TECALEMIT Страницы: 19
G-FITNESS AIR ROWER User Manual preview
AIR ROWER
Бренд: G-FITNESS Страницы: 26
Gaiam restore 05-63870 Setup, Workout Tips And Care & Safety Manual preview
05-63870
Бренд: Gaiam restore Страницы: 2
FujiFilm FCR PRIMA T2 Quick Manual preview
FCR PRIMA T2
Бренд: FujiFilm Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды