Keysight DSOX3012T Скачать руководство пользователя страница 32

Страница: 32 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Getting Started

To power-on the

oscilloscope

Connect the power cord to the rear of the oscilloscope, then to a suitable AC

voltage source. Route the power cord so the oscilloscope's feet and legs do not

pinch the cord.

The oscilloscope automatically adjusts for input line voltages in the range 100

to 240 VAC. The line cord provided is matched to the country of origin.

Press the power switch.

The power switch is located on the lower left corner of the front panel. The

oscilloscope will perform a self-test and will be operational in a few seconds.

Connect Probes to the Oscilloscope

Connect the oscilloscope probe to an oscilloscope channel BNC connector.

Connect the probe's retractable hook tip to the point of interest on the circuit or

device under test. Be sure to connect the probe ground lead to a ground point

on the circuit.

WARNING

Always use a grounded power cord. Do not defeat the power cord ground.

CAUTION

Maximum input voltage at analog inputs

135 Vrms
50

input: 5 Vrms Input protection is enabled in 50

mode and the 50

load will

disconnect if greater than 5 Vrms is detected. However the inputs could still be damaged,

depending on the time constant of the signal. The 50

input protection only functions

when the oscilloscope is powered on.

CAUTION

When measuring voltages over 30 V, use a 10:1 probe.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды