Keysight DSOX3012T Скачать руководство пользователя страница 201

Страница: 201 / 530

Triggers

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

201

oscilloscope will trigger on color field 1 alternating with color field 3 (see the

following figure). This setup can be used to measure the envelope of the reference

burst.

If a more detailed analysis is required, then only one color field should be selected

to be the trigger. You can do this by using the

Field Holdoff

softkey in the Video

Trigger Menu. Press the

Field Holdoff

softkey and use the Entry knob to adjust the

holdoff in half-field increments until the oscilloscope triggers on only one phase of

the color burst.

A quick way to synchronize to the other phase is to briefly disconnect the signal

and then reconnect it. Repeat until the correct phase is displayed.

When holdoff is adjusted using the

Field Holdoff

softkey and the Entry knob, the

corresponding holdoff time will be displayed in the Trigger Mode and Coupling

Menu.

Figure 32

Triggering on Color Field 1 Alternating with Color Field 3

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды