Keysight DSOX3012T Скачать руководство пользователя страница 514

Страница: 514 / 530

514

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

UART/RS232 Triggering and Serial Decode

•

Rx 1:Data

— For use when the device under test data words are 9 bits in

length including the alert bit (the 9th bit). Triggers only when the 9th (alert)

bit is 1. The specified data byte applies to the least significant 8 bits

(excludes the 9th (alert) bit).

•

Rx 0:Data

— For use when the device under test data words are 9 bits in

length including the alert bit (the 9th bit). Triggers only when the 9th (alert)

bit is 0. The specified data byte applies to the least significant 8 bits

(excludes the 9th (alert) bit).

•

Rx X:Data

— For use when the device under test data words are 9 bits in

length including the alert bit (the 9th bit). Triggers on a data byte that you

specify regardless of the value of the 9th (alert) bit. The specified data byte

applies to the least significant 8 bits (excludes the 9th (alert) bit).

•

Similar choices are available for Tx.

•

Rx or Tx Parity Error

— Triggers on a parity error based on the parity you have

set in the Bus Configuration Menu.

If you choose a trigger condition that includes "

Data

" in its description (for

example:

Rx Data

), then press the

Data is

softkey, and choose an equality

qualifier. You can choose equal to, not equal to, less than, or greater than a

specific data value.

Use the

Data

softkey to choose the data value for your trigger comparison. This

works in conjunction with the

Data is

softkey.

Optional: The

Burst

softkey lets you trigger on the Nth frame (1-4096) after an

idle time you select. All trigger conditions must be met for the trigger to occur.

Burst

is selected, an idle time (1 µs to 10 s) can be specified so that the

oscilloscope will look for a trigger condition only after the idle time has past.

Press the

Idle

softkey and rotate the Entry knob to set an idle time.

NOTE

If the setup does not produce a stable trigger, the UART/RS232 signals may be slow enough

that the oscilloscope is AutoTriggering. Press the

[Mode/Coupling]

key, then press the

Mode

softkey to set the trigger mode from

Auto

Normal

NOTE

To display UART/RS232 serial decode, see

“UART/RS232 Serial Decode"

on page 515.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды