Keysight DSOX3012T Скачать руководство пользователя страница 348

Страница: 348 / 530

348

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Utility Settings

To set up the screen saver

The oscilloscope can be configured to turn on a display screen saver when the

oscilloscope has been idle for a specified length of time.

Press

[Utility] > Options > Preferences > Screen Saver

to display the Screen Saver

Menu.

Press the

Screen Saver

softkey to select the screen saver type.

The screen saver can be set to

Off

, to display any of the images shown in the

list, or can display a user-defined text string.

User

is selected:

Press the

Text

softkey.

In the Text keypad dialog, you can enter text using:

•

The touch screen (when the front panel

[Touch]

key is lit).

•

The

Entry knob. Turn the knob to select a key in the dialog; then,

push the

Entry knob to enter it.

•

A connected USB keyboard.

•

A connected USB mouse — you can click anything on the screen that can

be touched.

When you are done entering text, select the dialog's Enter or OK key or press

the

Text

softkey again.

The user-defined screen saver text appears in the softkey.

Press the

Wait

softkey; then, turn the Entry knob to select the number of

minutes to wait before the selected screen saver activates.

When you turn the Entry knob, the number of minutes is displayed on the

Wait

softkey. The default time is 180 minutes (3 hours).

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды