Keysight DSOX3012T Скачать руководство пользователя страница 301

Страница: 301 / 530

301

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

19 Waveform Generator

To select generated waveform types and settings / 301
To edit arbitrary waveforms / 305
To output the waveform generator sync pulse / 312
To specify the expected output load / 312
To use waveform generator logic presets / 313
To add noise to the waveform generator output / 313
To add modulation to the waveform generator output / 314
To restore waveform generator defaults / 318

A waveform generator is built into the oscilloscope. It is enabled by the

DSOX3WAVEGEN upgrade license. The waveform generator gives you an easy

way to provide input signals when testing circuitry with the oscilloscope.

Waveform generator settings can be saved and recalled with oscilloscope setups.

See

Chapter 20

, “Save/Email/Recall (Setups, Screens, Data),” starting on page

321.

To select generated waveform types and settings

To access the Waveform Generator Menu and enable or disable the waveform

generator output on the front panel Gen Out BNC, press the

[Wave Gen]

key.

When waveform generator output is enabled, the

[Wave Gen]

key is illuminated.

When waveform generator output is disabled, the

[Wave Gen]

key is off.

The waveform generator output is always disabled when the instrument is first

turned on.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды