Keysight DSOX3012T Скачать руководство пользователя страница 380

Страница: 380 / 530

380

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Reference

Other Options Available

Upgrading to an MSO

A license can be installed to activate the digital channels of an oscilloscope that

was not originally ordered as a mixed-signal oscilloscope (MSO). A mixed signal

oscilloscope has analog channels plus 16 time-correlated digital timing channels.

For information about upgrading your oscilloscope through licensing, contact your

local Keysight Technologies representative or see

www.keysight.com/find/3000TX-Series

Software and Firmware Updates

From time to time Keysight Technologies releases software and firmware updates

for its products. To search for firmware updates for your oscilloscope, direct your

web browser to

www.keysight.com/find/3000TX-Series-sw

PWR

Power Measurement and Analysis.

Order DSOX3PWR.
You can find the

PWR Power Measurement

Application User's Guide

www.keysight.com/find/3000TX-Serie

s-manual

or on the Documentation CD.

SENSOR

SENT (Single Edge Nibble Transmission) Triggering and

Analysis.

Order DSOXT3SENSOR.

VID

Extended Video Triggering and Analysis.

Order DSOX3VID.

WAVEGEN

Waveform Generator.

Order DSOX3WAVEGEN.

Table 5

Licensed Options Available (continued)

License

Description

Upgrade model number, notes

Table 6

Calibration Option

Option

Order

A6J

ANSI Z540 Compliant Calibration

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды