Keysight DSOX3012T Скачать руководство пользователя страница 397

Страница: 397 / 530

CAN/LIN Triggering and Serial Decode

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

397

Press the

Back/Up key to return to the CAN Signals Menu.

When decoding CAN FD, press the

FD Rate Settings

softkey to open the CAN FD

Rate Settings Menu.

Press the

Baud

softkey; then, turn the Entry knob to match the CAN FD baud

rate of the signal from your device under test.

If the desired baud rate is not shown in the list, select

User Defined

and use

the

User Baud

softkey to set the baud rate.

The CAN FD baud rate can be set to predefined baud rates from 1-10 Mb/s

or a user-defined baud rate from 10.0 kb/s to 10 Mb/s in increments of

100 b/s.

If the baud rate you select does not match the CAN FD baud rate, false

triggers and decoding may occur.

Press the

Sample Point

softkey; then, turn the Entry knob to select the sample

point.

The sample point is the point during the bit time where the bit level is

sampled to determine whether it is dominant or recessive. The sample point

represents the percentage of time between the beginning of the bit time to

the end of the bit time.

60%

70%

80%

Sample Point

One Bit

Back

NOTE

For standard CAN, only the Standard Rate Settings must be set correctly. For CAN FD, both

the Standard Rate Settings and the FD Rate Settings must be set correctly.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды