Keysight DSOX3012T Скачать руководство пользователя страница 259

Страница: 259 / 530

Measurements

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

259

Counter

The InfiniiVision X-Series oscilloscopes have an integrated hardware frequency

counter which counts the number of cycles that occur within a period of time

(known as the gate time) to measure the frequency of a signal.

The gate time is the horizontal range of the oscilloscope but is limited to >= 0.1 s

and <= 10 s. Unlike other measurements, the Zoom horizontal timebase window

does not gate the Counter measurement.

The Counter measurement can measure frequencies up to the bandwidth of the

oscilloscope. The minimum frequency supported is 2.0 / gateTime.

The hardware counter uses the trigger comparator output. Therefore, the counted

channel's trigger level (or threshold for digital channels) must be set correctly.

Analog and digital channels can be selected as the source.

Only one Counter measurement can be displayed at a time.

Figure 49

Isolating an event for Frequency measurement

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды